2015 Husqvarna FC 350, Only 17 Hours! 2015 Husqvarna® FC 350 BALANCE AND PRECISION With top-level performance guaranteed by the lightweight agility of a 250 and the hard-hitting power of a 450, the FC 350 carves through turns effortlessly and powers down straights aggressively. Standard equipment such as the electric start system and the handlebar-mounted map switch highlight the FC 350 s technological edge over the competition. Features May Include: ENGINE With peak power of 54 horsepower in a package of roughly the same dimensions as the FC 250 engine, the FC 350 offers 450-class performance with 250-class size. Superb engineering and manufacturing expertise combine to make the impressive engine that powers the FC 350 to the top of the power output charts. The titanium valves are ultra-lightweight, weighing only 22.4g and have a diameter of 36.3mm each on the intake side, and 22.7g with a diameter of 29.1mm on the exhaust side. Combined with the Diamond Like Carbon (DLC) coated followers, the FC 350 engine is capable of reaching a 13,000 rpm ceiling. The yellow valve cover tops-off a technological marvel. The handlebar mounted map switch is a standard feature and allows the rider to switch between maps while riding, adjusting power delivery and engine performance according to rider fatigue and track conditions. ENGINE MANAGEMENT SYSTEM The electronic fuel injection and 44mm throttle body of the Keihin Engine Management System on the 4-stroke models, combine to offer amazing power delivery and efficiency at all engine speeds. The injector was positioned on the bottom of the inlet tract for optimal air-fuel mixture, resulting in crisp throttle response and class-leading power. Great attention was dedicated to ensuring that cleaning and washing the bike will not damage the electronics. The wire harness, lead wire, and high quality sealed critical connectors ensure that a jet wash poses no threat. The throttle position sensor (TPS) is also water resistant and protected. CRANKSHAFT, CONROD AND PISTON The plain big end bearing and two force-fitted shells that run directly on the crank pin are lubricated by the engine s pressure lubrication in order to maintain durability and long service intervals (100 hours before changing con rod, con rod bearing and crank pin). The FC 350 s power output and engine characteristics require the highest quality components, therefore the entire crankshaft, together with the con rod, is produced by industry leader Pankl. The CP-Carrillo forged box-type piston combines maximum performance and reliability with minimum weight, only 270g. The compression ratio is 13.65:1. FRAME The engineers in Research and Development had clear objectives in terms of torsional rigidity, longitudinal stiffness and weight. The goal was to give the rider optimal fee
2015 Husqvarna FC 350, Only 17 Hours! 2015 Husqvarna® FC 350 BALANCE AND PRECISION With top-level performance guaranteed by the lightweight agility of a 250 and the hard-hitting power of a 450, the FC 350 carves through turns effortlessly and powers down straights aggressively. Standard equipment such as the electric start system and the handlebar-mounted map switch highlight the FC 350 s technological edge over the competition. Features May Include: ENGINE With peak power of 54 horsepower in a package of roughly the same dimensions as the FC 250 engine, the FC 350 offers 450-class performance with 250-class size. Superb engineering and manufacturing expertise combine to make the impressive engine that powers the FC 350 to the top of the power output charts. The titanium valves are ultra-lightweight, weighing only 22.4g and have a diameter of 36.3mm each on the intake side, and 22.7g with a diameter of 29.1mm on the exhaust side. Combined with the Diamond Like Carbon (DLC) coated followers, the FC 350 engine is capable of reaching a 13,000 rpm ceiling. The yellow valve cover tops-off a technological marvel. The handlebar mounted map switch is a standard feature and allows the rider to switch between maps while riding, adjusting power delivery and engine performance according to rider fatigue and track conditions. ENGINE MANAGEMENT SYSTEM The electronic fuel injection and 44mm throttle body of the Keihin Engine Management System on the 4-stroke models, combine to offer amazing power delivery and efficiency at all engine speeds. The injector was positioned on the bottom of the inlet tract for optimal air-fuel mixture, resulting in crisp throttle response and class-leading power. Great attention was dedicated to ensuring that cleaning and washing the bike will not damage the electronics. The wire harness, lead wire, and high quality sealed critical connectors ensure that a jet wash poses no threat. The throttle position sensor (TPS) is also water resistant and protected. CRANKSHAFT, CONROD AND PISTON The plain big end bearing and two force-fitted shells that run directly on the crank pin are lubricated by the engine s pressure lubrication in order to maintain durability and long service intervals (100 hours before changing con rod, con rod bearing and crank pin). The FC 350 s power output and engine characteristics require the highest quality components, therefore the entire crankshaft, together with the con rod, is produced by industry leader Pankl. The CP-Carrillo forged box-type piston combines maximum performance and reliability with minimum weight, only 270g. The compression ratio is 13.65:1. FRAME The engineers in Research and Development had clear objectives in terms of torsional rigidity, longitudinal stiffness and weight. The goal was to give the rider optimal fee
2014 Husqvarna FC 250, Super clean FC250. Low Hours. 2014 Husqvarna FC 250 High tech race weapon The MX2 category has a new contender. The FC 250, with its powerful, high-revving and compact 250cc 4-stroke engine, sharp handling, light weight and extreme agility, takes it straight to the top. The 14,000 RPM rev limit clearly indicates the FC 250's potential. Experts and amateurs alike are sure to appreciate the electric start for peace of mind in every circumstance. Super sharp throttle response, smooth clutch action and precise shifting pave the way to a holeshot.
2014 Husqvarna FC 250, Super clean FC250. Low Hours. 2014 Husqvarna FC 250 High tech race weapon The MX2 category has a new contender. The FC 250, with its powerful, high-revving and compact 250cc 4-stroke engine, sharp handling, light weight and extreme agility, takes it straight to the top. The 14,000 RPM rev limit clearly indicates the FC 250's potential. Experts and amateurs alike are sure to appreciate the electric start for peace of mind in every circumstance. Super sharp throttle response, smooth clutch action and precise shifting pave the way to a holeshot.
2017 Husqvarna FC 250, 2017 Husqvarna® FC 250 RAZOR-SHARP AGILITY The 250cc DOHC engine has been designed in conjunction with the chassis to operate in perfect harmony. All internal components have been engineered to deliver the maximum performance and packaged in order to position the engine at the ideal centre of gravity within the chromoly steel frame. In combination with the carbon fibre rear subframe and new WP AER 48 front fork, the FC 250 is one of the most technologically advanced 250 4T motocrossers ever developed. Features may include: Engine All major components and shaft arrangements have been carefully designed and placed in specific positions that best suit the performance and handling characteristics of the FC 250. The 250 cc engine is not only light at 26.1 kg but also remarkably powerful with an overall power output of 46 hp at the output shaft. One way in which this was achieved was by engineering key components to produce the least amount of friction possible, reducing drag as a result. DOHC cylinder head The DOHC cylinder head features finger followers with a DLC (diamond like carbon) coating resulting in minimal friction and optimal performance. These actuate large titanium valves (32.5 mm intake, 26.5 mm exhaust) which at the 14,000 rpm rev-limit open and close multiple times each second introducing fuel/air mixture to the carefully designed combustion chamber delivering efficient and optimal power throughout the rev-range. The cylinder head is now fixed to the frame using lightweight aluminium brackets saving 114 grams while keeping the same structural integrity. Crankcases The aluminium crankcases have been designed to house the internal components of the engine in the perfect position to achieve the ideal centre of gravity. The lightweight casings are manufactured using a high-pressure die cast production process, resulting in thin wall thickness while retaining exceptional reliability. The iconic Husqvarna logo adorns the bronze finished crankcase covers. Exhaust system The FC 250 exhaust system has been expertly designed to deliver the best possible performance while adhering to the FIM noise limits. The header pipe features a resonance chambers for optimal performance while the silencer is crafted from lightweight and strong aluminium. Magura hydraulic clutch The FC 250 features a Magura hydraulic clutch system. The high quality German-made clutch system guarantees even wear, almost maintenance-free operation and perfect modulation in every condition. This means that play is constantly compensated so that the pressure point and function of the clutch remain identical in cold or hot conditions, as well as over time. CSS clutch The 250 cc and 350 cc engines feature a CSS (coil spring steel) clutch with Magura hydraulics and lever. The CSS clu
2017 Husqvarna FC 250, 2017 Husqvarna® FC 250 RAZOR-SHARP AGILITY The 250cc DOHC engine has been designed in conjunction with the chassis to operate in perfect harmony. All internal components have been engineered to deliver the maximum performance and packaged in order to position the engine at the ideal centre of gravity within the chromoly steel frame. In combination with the carbon fibre rear subframe and new WP AER 48 front fork, the FC 250 is one of the most technologically advanced 250 4T motocrossers ever developed. Features may include: Engine All major components and shaft arrangements have been carefully designed and placed in specific positions that best suit the performance and handling characteristics of the FC 250. The 250 cc engine is not only light at 26.1 kg but also remarkably powerful with an overall power output of 46 hp at the output shaft. One way in which this was achieved was by engineering key components to produce the least amount of friction possible, reducing drag as a result. DOHC cylinder head The DOHC cylinder head features finger followers with a DLC (diamond like carbon) coating resulting in minimal friction and optimal performance. These actuate large titanium valves (32.5 mm intake, 26.5 mm exhaust) which at the 14,000 rpm rev-limit open and close multiple times each second introducing fuel/air mixture to the carefully designed combustion chamber delivering efficient and optimal power throughout the rev-range. The cylinder head is now fixed to the frame using lightweight aluminium brackets saving 114 grams while keeping the same structural integrity. Crankcases The aluminium crankcases have been designed to house the internal components of the engine in the perfect position to achieve the ideal centre of gravity. The lightweight casings are manufactured using a high-pressure die cast production process, resulting in thin wall thickness while retaining exceptional reliability. The iconic Husqvarna logo adorns the bronze finished crankcase covers. Exhaust system The FC 250 exhaust system has been expertly designed to deliver the best possible performance while adhering to the FIM noise limits. The header pipe features a resonance chambers for optimal performance while the silencer is crafted from lightweight and strong aluminium. Magura hydraulic clutch The FC 250 features a Magura hydraulic clutch system. The high quality German-made clutch system guarantees even wear, almost maintenance-free operation and perfect modulation in every condition. This means that play is constantly compensated so that the pressure point and function of the clutch remain identical in cold or hot conditions, as well as over time. CSS clutch The 250 cc and 350 cc engines feature a CSS (coil spring steel) clutch with Magura hydraulics and lever. The CSS clu
2017 Husqvarna FC 250, 2017 Husqvarna® FC 250 RAZOR-SHARP AGILITY The 250cc DOHC engine has been designed in conjunction with the chassis to operate in perfect harmony. All internal components have been engineered to deliver the maximum performance and packaged in order to position the engine at the ideal centre of gravity within the chromoly steel frame. In combination with the carbon fibre rear subframe and new WP AER 48 front fork, the FC 250 is one of the most technologically advanced 250 4T motocrossers ever developed. Features may include: Engine All major components and shaft arrangements have been carefully designed and placed in specific positions that best suit the performance and handling characteristics of the FC 250. The 250 cc engine is not only light at 26.1 kg but also remarkably powerful with an overall power output of 46 hp at the output shaft. One way in which this was achieved was by engineering key components to produce the least amount of friction possible, reducing drag as a result. DOHC cylinder head The DOHC cylinder head features finger followers with a DLC (diamond like carbon) coating resulting in minimal friction and optimal performance. These actuate large titanium valves (32.5 mm intake, 26.5 mm exhaust) which at the 14,000 rpm rev-limit open and close multiple times each second introducing fuel/air mixture to the carefully designed combustion chamber delivering efficient and optimal power throughout the rev-range. The cylinder head is now fixed to the frame using lightweight aluminium brackets saving 114 grams while keeping the same structural integrity. Crankcases The aluminium crankcases have been designed to house the internal components of the engine in the perfect position to achieve the ideal centre of gravity. The lightweight casings are manufactured using a high-pressure die cast production process, resulting in thin wall thickness while retaining exceptional reliability. The iconic Husqvarna logo adorns the bronze finished crankcase covers. Exhaust system The FC 250 exhaust system has been expertly designed to deliver the best possible performance while adhering to the FIM noise limits. The header pipe features a resonance chambers for optimal performance while the silencer is crafted from lightweight and strong aluminium. Magura hydraulic clutch The FC 250 features a Magura hydraulic clutch system. The high quality German-made clutch system guarantees even wear, almost maintenance-free operation and perfect modulation in every condition. This means that play is constantly compensated so that the pressure point and function of the clutch remain identical in cold or hot conditions, as well as over time. CSS clutch The 250 cc and 350 cc engines feature a CSS (coil spring steel) clutch with Magura hydraulics and lever. The CSS clu
2017 Husqvarna FC 250, 2017 Husqvarna® FC 250 RAZOR-SHARP AGILITY The 250cc DOHC engine has been designed in conjunction with the chassis to operate in perfect harmony. All internal components have been engineered to deliver the maximum performance and packaged in order to position the engine at the ideal centre of gravity within the chromoly steel frame. In combination with the carbon fibre rear subframe and new WP AER 48 front fork, the FC 250 is one of the most technologically advanced 250 4T motocrossers ever developed. Features may include: Engine All major components and shaft arrangements have been carefully designed and placed in specific positions that best suit the performance and handling characteristics of the FC 250. The 250 cc engine is not only light at 26.1 kg but also remarkably powerful with an overall power output of 46 hp at the output shaft. One way in which this was achieved was by engineering key components to produce the least amount of friction possible, reducing drag as a result. DOHC cylinder head The DOHC cylinder head features finger followers with a DLC (diamond like carbon) coating resulting in minimal friction and optimal performance. These actuate large titanium valves (32.5 mm intake, 26.5 mm exhaust) which at the 14,000 rpm rev-limit open and close multiple times each second introducing fuel/air mixture to the carefully designed combustion chamber delivering efficient and optimal power throughout the rev-range. The cylinder head is now fixed to the frame using lightweight aluminium brackets saving 114 grams while keeping the same structural integrity. Crankcases The aluminium crankcases have been designed to house the internal components of the engine in the perfect position to achieve the ideal centre of gravity. The lightweight casings are manufactured using a high-pressure die cast production process, resulting in thin wall thickness while retaining exceptional reliability. The iconic Husqvarna logo adorns the bronze finished crankcase covers. Exhaust system The FC 250 exhaust system has been expertly designed to deliver the best possible performance while adhering to the FIM noise limits. The header pipe features a resonance chambers for optimal performance while the silencer is crafted from lightweight and strong aluminium. Magura hydraulic clutch The FC 250 features a Magura hydraulic clutch system. The high quality German-made clutch system guarantees even wear, almost maintenance-free operation and perfect modulation in every condition. This means that play is constantly compensated so that the pressure point and function of the clutch remain identical in cold or hot conditions, as well as over time. CSS clutch The 250 cc and 350 cc engines feature a CSS (coil spring steel) clutch with Magura hydraulics and lever. The CSS clu
2017 Husqvarna FC 350, 2017 Husqvarna® FC 350 POWER AND CONTROL The FC 350 shares much of its engine and chassis architecture with the smaller FC 250 but with a maximum output of 58 hp, the FC 350 has a 450 rivalling power-to-weight ratio while keeping the light, agile handling of the 250. This is coupled with an advanced electronics package featuring launch control, switchable engine maps and traction control resulting in a versatile, high performance package. Features may include: Engine The 350 cc DOHC engine weighs in at only 27.2 kg with a maximum power output of 58 hp. The engine is specifically designed with performance, weight and mass centralisation as key areas. As a result, all shaft arrangements have been positioned to allow oscillating masses to occupy the ideal centre of gravity while all parts are engineered to offer the best performance while adding the least possible weight. Cylinder head The FC 350 features a DOHC design with polished camshafts and DLC coated finger followers. These components significantly reduce friction and improve overall performance. Added to the design are large titanium valves (36.3 mm intake and 29.1 mm exhaust) which allow the engine to rev freely to the 13,400 rpm ceiling. Cylinder and piston The 88mm bore cylinder features a large diameter and lightweight forged bridged-box-type piston produced by CP. As a result, the relatively low oscillating masses deliver exceptional power, high revs and a very wide power band. The compression ratio is 14:1. Crankshaft A perfectly balanced crankshaft is at the heart of the high output, high-reving, FC 350 engine. A plain big end bearing comprising of two force-fitted bearing shells ensure maximum reliability and durability, guaranteeing long service intervals of 100 hours. New map switch The FC 350 features a new handlebar map switch. Optimised for easy operation, the new map switch now selects between two engine maps, operates launch control and activates a new traction control feature. Traction control works by analysing throttle input from the rider and the rate at which the RPM increases. If the RPM increases too quickly, the EMS will register a loss of grip and reduce the amount of power to the rear wheel ensuring maximum traction. Engine management system The Keihin EMS is specifically designed to be smaller, lighter and faster at processing data. It integrates launch control for perfect starts, selectable engine maps as well as traction control. Additionally, via a gear sensor, the EMS selects a power delivery tailored for each gear. 44 mm throttle body The FC 350 features a 44 mm Keihin throttle body. The injector has been positioned to ensure the most efficient flow of fuel into the combustion chamber while, in an effort to ensure optimal throttle response, the throttle cable is mounted directly without a throttle l
2017 Husqvarna FC 350, 2017 Husqvarna® FC 350 POWER AND CONTROL The FC 350 shares much of its engine and chassis architecture with the smaller FC 250 but with a maximum output of 58 hp, the FC 350 has a 450 rivalling power-to-weight ratio while keeping the light, agile handling of the 250. This is coupled with an advanced electronics package featuring launch control, switchable engine maps and traction control resulting in a versatile, high performance package. Features may include: Engine The 350 cc DOHC engine weighs in at only 27.2 kg with a maximum power output of 58 hp. The engine is specifically designed with performance, weight and mass centralisation as key areas. As a result, all shaft arrangements have been positioned to allow oscillating masses to occupy the ideal centre of gravity while all parts are engineered to offer the best performance while adding the least possible weight. Cylinder head The FC 350 features a DOHC design with polished camshafts and DLC coated finger followers. These components significantly reduce friction and improve overall performance. Added to the design are large titanium valves (36.3 mm intake and 29.1 mm exhaust) which allow the engine to rev freely to the 13,400 rpm ceiling. Cylinder and piston The 88mm bore cylinder features a large diameter and lightweight forged bridged-box-type piston produced by CP. As a result, the relatively low oscillating masses deliver exceptional power, high revs and a very wide power band. The compression ratio is 14:1. Crankshaft A perfectly balanced crankshaft is at the heart of the high output, high-reving, FC 350 engine. A plain big end bearing comprising of two force-fitted bearing shells ensure maximum reliability and durability, guaranteeing long service intervals of 100 hours. New map switch The FC 350 features a new handlebar map switch. Optimised for easy operation, the new map switch now selects between two engine maps, operates launch control and activates a new traction control feature. Traction control works by analysing throttle input from the rider and the rate at which the RPM increases. If the RPM increases too quickly, the EMS will register a loss of grip and reduce the amount of power to the rear wheel ensuring maximum traction. Engine management system The Keihin EMS is specifically designed to be smaller, lighter and faster at processing data. It integrates launch control for perfect starts, selectable engine maps as well as traction control. Additionally, via a gear sensor, the EMS selects a power delivery tailored for each gear. 44 mm throttle body The FC 350 features a 44 mm Keihin throttle body. The injector has been positioned to ensure the most efficient flow of fuel into the combustion chamber while, in an effort to ensure optimal throttle response, the throttle cable is mounted directly without a throttle l
2017 Husqvarna FC 350, 2017 Husqvarna® FC 350 POWER AND CONTROL The FC 350 shares much of its engine and chassis architecture with the smaller FC 250 but with a maximum output of 58 hp, the FC 350 has a 450 rivalling power-to-weight ratio while keeping the light, agile handling of the 250. This is coupled with an advanced electronics package featuring launch control, switchable engine maps and traction control resulting in a versatile, high performance package. Features may include: Engine The 350 cc DOHC engine weighs in at only 27.2 kg with a maximum power output of 58 hp. The engine is specifically designed with performance, weight and mass centralisation as key areas. As a result, all shaft arrangements have been positioned to allow oscillating masses to occupy the ideal centre of gravity while all parts are engineered to offer the best performance while adding the least possible weight. Cylinder head The FC 350 features a DOHC design with polished camshafts and DLC coated finger followers. These components significantly reduce friction and improve overall performance. Added to the design are large titanium valves (36.3 mm intake and 29.1 mm exhaust) which allow the engine to rev freely to the 13,400 rpm ceiling. Cylinder and piston The 88mm bore cylinder features a large diameter and lightweight forged bridged-box-type piston produced by CP. As a result, the relatively low oscillating masses deliver exceptional power, high revs and a very wide power band. The compression ratio is 14:1. Crankshaft A perfectly balanced crankshaft is at the heart of the high output, high-reving, FC 350 engine. A plain big end bearing comprising of two force-fitted bearing shells ensure maximum reliability and durability, guaranteeing long service intervals of 100 hours. New map switch The FC 350 features a new handlebar map switch. Optimised for easy operation, the new map switch now selects between two engine maps, operates launch control and activates a new traction control feature. Traction control works by analysing throttle input from the rider and the rate at which the RPM increases. If the RPM increases too quickly, the EMS will register a loss of grip and reduce the amount of power to the rear wheel ensuring maximum traction. Engine management system The Keihin EMS is specifically designed to be smaller, lighter and faster at processing data. It integrates launch control for perfect starts, selectable engine maps as well as traction control. Additionally, via a gear sensor, the EMS selects a power delivery tailored for each gear. 44 mm throttle body The FC 350 features a 44 mm Keihin throttle body. The injector has been positioned to ensure the most efficient flow of fuel into the combustion chamber while, in an effort to ensure optimal throttle response, the throttle cable is mounted directly without a throttle l
2017 Husqvarna FC 250, 2017 Husqvarna® FC 250 RAZOR-SHARP AGILITY The 250cc DOHC engine has been designed in conjunction with the chassis to operate in perfect harmony. All internal components have been engineered to deliver the maximum performance and packaged in order to position the engine at the ideal centre of gravity within the chromoly steel frame. In combination with the carbon fibre rear subframe and new WP AER 48 front fork, the FC 250 is one of the most technologically advanced 250 4T motocrossers ever developed. Features may include: Engine All major components and shaft arrangements have been carefully designed and placed in specific positions that best suit the performance and handling characteristics of the FC 250. The 250 cc engine is not only light at 26.1 kg but also remarkably powerful with an overall power output of 46 hp at the output shaft. One way in which this was achieved was by engineering key components to produce the least amount of friction possible, reducing drag as a result. DOHC cylinder head The DOHC cylinder head features finger followers with a DLC (diamond like carbon) coating resulting in minimal friction and optimal performance. These actuate large titanium valves (32.5 mm intake, 26.5 mm exhaust) which at the 14,000 rpm rev-limit open and close multiple times each second introducing fuel/air mixture to the carefully designed combustion chamber delivering efficient and optimal power throughout the rev-range. The cylinder head is now fixed to the frame using lightweight aluminium brackets saving 114 grams while keeping the same structural integrity. Crankcases The aluminium crankcases have been designed to house the internal components of the engine in the perfect position to achieve the ideal centre of gravity. The lightweight casings are manufactured using a high-pressure die cast production process, resulting in thin wall thickness while retaining exceptional reliability. The iconic Husqvarna logo adorns the bronze finished crankcase covers. Exhaust system The FC 250 exhaust system has been expertly designed to deliver the best possible performance while adhering to the FIM noise limits. The header pipe features a resonance chambers for optimal performance while the silencer is crafted from lightweight and strong aluminium. Magura hydraulic clutch The FC 250 features a Magura hydraulic clutch system. The high quality German-made clutch system guarantees even wear, almost maintenance-free operation and perfect modulation in every condition. This means that play is constantly compensated so that the pressure point and function of the clutch remain identical in cold or hot conditions, as well as over time. CSS clutch The 250 cc and 350 cc engines feature a CSS (coil spring steel) clutch with Magura hydraulics and lever. The CSS clutch has six coil springs and 7 clutch plates in a one-
2017 Husqvarna FC 350, 2017 Husqvarna® FC 350 POWER AND CONTROL The FC 350 shares much of its engine and chassis architecture with the smaller FC 250 but with a maximum output of 58 hp, the FC 350 has a 450 rivalling power-to-weight ratio while keeping the light, agile handling of the 250. This is coupled with an advanced electronics package featuring launch control, switchable engine maps and traction control resulting in a versatile, high performance package. Features may include: Engine The 350 cc DOHC engine weighs in at only 27.2 kg with a maximum power output of 58 hp. The engine is specifically designed with performance, weight and mass centralisation as key areas. As a result, all shaft arrangements have been positioned to allow oscillating masses to occupy the ideal centre of gravity while all parts are engineered to offer the best performance while adding the least possible weight. Cylinder head The FC 350 features a DOHC design with polished camshafts and DLC coated finger followers. These components significantly reduce friction and improve overall performance. Added to the design are large titanium valves (36.3 mm intake and 29.1 mm exhaust) which allow the engine to rev freely to the 13,400 rpm ceiling. Cylinder and piston The 88mm bore cylinder features a large diameter and lightweight forged bridged-box-type piston produced by CP. As a result, the relatively low oscillating masses deliver exceptional power, high revs and a very wide power band. The compression ratio is 14:1. Crankshaft A perfectly balanced crankshaft is at the heart of the high output, high-reving, FC 350 engine. A plain big end bearing comprising of two force-fitted bearing shells ensure maximum reliability and durability, guaranteeing long service intervals of 100 hours. New map switch The FC 350 features a new handlebar map switch. Optimised for easy operation, the new map switch now selects between two engine maps, operates launch control and activates a new traction control feature. Traction control works by analysing throttle input from the rider and the rate at which the RPM increases. If the RPM increases too quickly, the EMS will register a loss of grip and reduce the amount of power to the rear wheel ensuring maximum traction. Engine management system The Keihin EMS is specifically designed to be smaller, lighter and faster at processing data. It integrates launch control for perfect starts, selectable engine maps as well as traction control. Additionally, via a gear sensor, the EMS selects a power delivery tailored for each gear. 44 mm throttle body The FC 350 features a 44 mm Keihin throttle body. The injector has been positioned to ensure the most efficient flow of fuel into the combustion chamber while, in an effort to ensure optimal throttle response, the throttle cable is mounted directly without a throttle l
2017 Husqvarna FC 450, Husqvarna FC 450 2017 model . Call 708-588-9900 for pricing . 2017 Husqvarna® FC 450 MUSCULAR PERFORMANCE The flagship FC 450 offers class leading performance in a lightweight, capable package. Every aspect is designed to offer exceptional performance in conjunction with rider comfort and ergonomics making the FC 450 equally appealing to amateur and professional riders alike. Traction control, map select and WP AER 48 forks are just a few of the standard features which ensure the highest levels of performance and premium quality. Features may include: New map switch The FC 450 features a new handlebar map switch. Optimised for easy operation, the new map switch now selects between two engine maps, operates launch control and activates a new traction control feature. Traction control works by analysing throttle input from the rider and the rate at which the RPM increases. If the RPM increases too quickly, the EMS will register a loss of grip and reduce the amount of power to the rear wheel ensuring maximum traction. Engine management system The Keihin EMS is specifically designed to be smaller, lighter and faster at processing data. It integrates launch control for perfect starts, selectable engine maps as well as traction control. Additionally, via a gear sensor, the EMS selects a power delivery tailored for each gear. 44 mm throttle body The FC 450 features a 44 mm Keihin throttle body. The injector is positioned to ensure the most efficient flow of fuel into the combustion chamber while, in an effort to ensure optimal throttle response, the throttle cable is mounted directly without a throttle linkage providing more immediate throttle response and feeling Electric start and Li-Ion battery Along with the benefit of easy starting, the standard electric starting system is combined with a compact Li-Ion battery which is 1 kg lighter than a conventional battery. Crankshaft The inertia produced by the crankshaft has been carefully calculated to deliver optimal traction and ride-ability from the powerful 450cc plant. Perfectly positioned, the component harnesses the rotating mass at the ideal centre of gravity resulting in a lightweight and agile handling feel. A plain big end bearing comprising of two force-fitted bearing shells ensure maximum reliability and durability, guaranteeing long service intervals of 100 hours. CNC machined triple clamps The black-anodised CNC machined triple clamps feature a rubber damping system that reduces vibration, increasing comfort. Additionally, the triple clamps have been meticulously designed to evenly distribute the clamping force on the fork leg, maximizing contact area for optimal sensitivity and minimum friction. For MY17 the upper triple clamp has been re-designed to compliment the new WP AER48 front forks. Magura hydraulic clutch The
2016 Husqvarna FC 450, Check us out for a great selection of new Husqvarna's . . 708-588-9900 . Ask for the deal ! 2016 Husqvarna® FC 450 MUSCULAR PERFORMANCE The ground-breaking new generation chassis is fitted with the most powerful Husqvarna motocross engine ever developed. The 63 horsepower single-overhead-cam 450 cc power plant has been completely redesigned; it is now smaller and lighter and has been completely reconfigured for optimal mass-centralisation within the new chromoly steel frame. The new bodywork elevates the riding experience thanks to accurately developed ergonomics that focus on instilling rider confidence, complete control and reduced fatigue. Features May Include: NEW ENGINE The new SOHC engine is 23 mm shorter, 23 mm narrower and 9 mm lower than the previous generation. Every internal component was revised and repositioned, lowering weight by an astonishing 1.8 kg for an overall weight of 27.8kg, increasing power to 63 hp and improving torque along the entire rev-range. Mass-centralisation was a key development factor, enabling chassis engineers to position the engine closer to the centre of gravity for greatly improved handling and manoeuvrability. Vibrations are kept to a minimum thanks to a multifunctional counter balance shaft that also drives the water pump and timing chain. NEW GEARBOX A lighter and more compact 5-speed gearbox is 8 mm narrower and 350 g lighter than the previous generation. The new surface treatment on 1st and 5th gears improves reliability, and combined with a new low-friction coating on the shifting fork and a redesigned shift drum, guarantee smooth and precise shifting. The gear lever features a new tip design that prevents dirt build-up. An advanced gear sensor allows for specific engine maps in each gear. NEW FRAME With years of experience in designing the most advanced steel frames in offroad, the engineers in Research and Development have designed a completely new chromium molibdenum steel frame that redefines every structural aspect in order to improve handling, ergonomics and packaging. The torsional rigidity and longitudinal stiffness have been completely rethought. The 6mm wider and 2mm lower steel tubes offer 20% more torsional rigidity and 30% less longitudinal stiffness compared to the previous generation frame design. These characteristics, matched to the new engine stays, improve handling precision while at the same time increasing bump-absorption and feeling. NEW CRANKSHAFT The new crankshaft features 10% more inertia and has been repositioned 9 mm backwards and 7 mm higher. The higher inertia increases traction and rideability while the new position within the engine contributes to mass-centralisation. A plain big end bearing and two force-fitted bearing shells ensure maximum reliability and durability, guaranteeing long service inte
